RV Technician Training Courses
Motorhome and Travel Trailer Repair (Basic)
(400 Hrs., 10 Wks)
COURSES
RV – 01 : NOMENCLATURE
Class/Lab : 8 Hours
An introduction into the Recreation Vehicle Industry. Students will learn to differentiate the distinct characteristics of each recreational vehicle classification. Also to include glossary of terms, parts suppliers, manufacturers, RV clubs and more.
RV – 02 : SERVICE TECHNICIAN (LIABILITY)
Class/Lab : 8 Hours
A presentation on service technician liability. The student will learn different aspects of various topics such as: SAFETY FIRST, work orders, lawsuit protection, starting a business(LLC, etc), general shop and shop safety.
RV – 03 : REPAIR MATERIAL
Class/Lab : 8 Hours
In this course the student will be introduced and familiarized with fasteners and sealers used on the exterior and interior of the recreational vehicle. Numerous materials and products used in RV construction will be demonstrated and discussed.
RV – 04 : BASIC RV ELECTRICITY
Class/Lab : 12 Hours
The student will be introduced to the theory of basic electricity and will learn the primary sources of electromotive force(emf). Further introduction will include AC vs DC, OHM’S Law, WATT’s Law, diagrams, schematics and symbols. How to use a VOM(volt-ohm-milliammeter), electrical circuits & components hands-on along with glossary of electrical terms.
RV – 05 : LP GAS
Class/Lab : 12 Hours
Inherently, LP gas systems are a viable part of most recreational vehicles. In this course, the student will learn “SAFETY FIRST,” glossary of terms, LP physical properties, RV LP system testing, LP containers, RV LP regulators, piping & tubing and RV LP codes & standards.
RV – 06 : BASIC RV PLUMBING
Class/Lab : 12 Hours
An essential part of any recreational vehicle is the plumbing systems. In this course the plumbing system will be split into two primary systems: The water distribution system and the waste water drainage system. All aspects of each system will be covered in these two sections. Also to include components and glossary of terms.
RV – 07 : APPLIANCE R & R
Class/Lab : 8 Hours
The appliances used in the recreational vehicle industry are similar to those used in the common residential home, though they vary distinctively. The Student will learn these differences during the overall RV Technician Training Course. While in this particular section they will learn location and proper removal and replacement of RV appliances and components used in the recreational vehicle.
RV – 08 : ACCESSORIES (Awnings, Antennas, Jacks, etc.)
Class/Lab : 16 Hours
Full size awnings may be installed using manufacturer’s instructions. Service and troubleshooting will be taught by using hardware from Carefree and A&E material and manuals. Students will learn how to install and/or service jacks and levelors, and antennas.
RV – 09 : BRAKES AND WIRING
Class/Lab : 16 Hours
The Student will use Tekonsha Industries materials and manuals for the hands-on learning of brake repair and troubleshooting. Tekonsha manuals and products will be used to give the students a thorough understanding of hydraulic surge brakes. The student will be taught how to install an electronic and a hydraulic/electronic brake control device. Tekonsha products and manuals will be used to install brake control devices.
RV – 10 : HITCH AND WIRING
Class/Lab : 16 Hours
Video tapes and manuals from the manufacturers will be used to instruct the students on the understanding of weight and distribution and forces generated between tow and recreational vehicles. The student will learn how to “match the hitch to the vehicle” for safe operation. The student will learn how to install a hitch on a vehicle. Since each application is different, it is very important that they learn how to read and follow the manufacturers directions “Exactly”. The student will be taught how to isolate all wires that operate the lights and brakes that are powered from the tow vehicle.
RV – 11 : ADVANCED R.V. ELECTRICITY
Class/Lab : 40 Hours
This is a more advanced study of AC and DC electricity as it is applied to the RV Industry. Students will learn how to read wiring schematics and apply this knowledge to the troubleshooting and repair of the appliances and accessories used in the RV. Initial instruction will also focus on converters and inverters. Since there are inherent dangers associated with this field of study, SAFETY FIRST, will be very heavily emphasized. It should be noted for the student that the repair of nearly all appliances and accessories depend on both AC and DC power. The study of Electricity, therefore, may be the most critical for the RV Technician and deserves the utmost concentration and mastery. Solar power, as it may apply to the RV, will also be covered.
RV – 12 : WATER SYSTEMS, FRESH AND WASTE
Class/Lab : 16 Hours
After a brief session on theory, the student will receive hands-on instruction on the operation, service and troubleshooting of the entire water system. This includes: plumbing supplies and manuals supplied by Quest, toilets and manuals provided by Thetford and SeaLand, pumps and manuals provided by ITT Jabsco and Shurflo, and Flojet fresh and waste water holding tanks from Riblet. The student will also learn how to repair water systems using all copper, all plastic and a combination of both. Check – valves, waste valves, and accumulator tanks will be covered in this course. Students will learn how to winterize an RV’s water system properly.
RV – 13 : WATER HEATERS
Class/Lab : 14 Hours
A brief session on theory will be followed by instruction on the operation, service, troubleshooting and installation of several water heaters. Pilot models as well as direct spark ignition models will be used. Safety will be emphasized during instruction on the L.P. gas system and water pressure and relief valves.
RV – 14 : RANGES AND OVENS
Class/Lab : 12 Hours
Several different models of ranges and ovens will be used in the hands-on instruction of this unit. Operation, service, troubleshooting and installation will also be taught.
RV – 15 : FURNACES
Class/Lab : 40 Hours
Operation, service, installation and extensive hands-on troubleshooting of older as well as more modern electronic ignition furnaces will be covered in detail. Careful attention will be placed on L.P., gas. SAFETY FIRST will be emphasized. Several models of furnaces will be used.
RV – 16 : ABSORPTION REFRIGERATION
Class/Lab : 40 Hours
The absorber system theory of refrigeration will be held for approximately eight (8) hours. Students will then have hands-on instruction in the operation, service, troubleshooting and installation of refrigerators. Both the older and newer electronic models will be used.
RV – 17 : AIR CONDITIONERS
Class/Lab : 40 Hours
This course will be introduced by the study of the theory of refrigeration. Students will learn operation, service, troubleshooting and installation of Duo Therm’s Brisk Air “Heat Pumps” and Penguin Coleman’s Mach l, lll and Delta and Emerson’s Quiet Kool air conditioners. The course on air conditioning will include hands-on instruction on repair and replacement of the cooling unit.
RV – 18 : GENERATORS
Class/Lab : 40 Hours
An increasing number of recreational vehicles are now equipped with generators and dealers have an increasing need for technicians who can do troubleshooting and make repairs. Several models of generators and manuals will be used to provide hands-on training to learn the proper operation and troubleshooting and service techniques of generators. Onan manuals will be used for schematic troubleshooting. Wiring diagrams and schematics are covered in detail.
RV – 19 : BODY DAMAGE
Class/Lab : 20 Hours
This course will cover estimating the cost and practical applications of making body repairs. The student will be shown how to evaluate the extent of both visual and, all too often hidden, damage of delamination, collision and floor and roof rot. Students will learn how to estimate the cost of these repairs and determine whether repair is practical. Checklists from local insurance adjusters, RV damage repair estimators and experience RV instructors will be used to provide the instruction. The student will then be introduced to the special tools and sealers used in coach repair.
RV – 20 : PDI & SLIDES
Class/Lab : 16 Hours
In this inclusive course the student will learn not only the purpose and definition of a PDI(Pre-Delivery Inspection), they will actually be guided step-by-step on how to properly perform a PDI using a late-model, typical recreational vehicle. The student will also spend class and lab time learning the operation, function, maintenance, adjustment and repair of the most common slide systems both hydraulic and electric types used on recreational vehicles.
RV – 21 : MASTER CERTIFICATION TEST
Class/Lab : 6 Hours
On this final day of the 10 week training course the student will take the Master Certification Test, after passing this test the student will be issued his “Certified RV Technician” certificate. After documented proof of one full year of successful full-time RV service performance the student will be awarded the explicit “Master RV Technician” certificate.
